Steel Flat Bar

Send Inquiry
Steel Flat Bar
Details
Steel flat bars are solid rectangular carbon or alloy steel sections produced via hot rolling or cold drawing.
Category
Structural Steel
Share to
Description

Steel flat bars are solid rectangular carbon or alloy steel sections produced via hot rolling or cold drawing. Hot-rolled flat bars serve general structural applications where yield strength and cost efficiency are primary, while cold-drawn flat bars provide tighter dimensional tolerances, sharper 90-degree corners, and smooth surface finishes required for precision machining, linear guides, and tooling fixtures.

 

Key Product Characteristics

 

Dimensional Consistency: Hot-rolled edge radius per ASTM A6 / EN 10058; cold-drawn side straightness within 1.0 mm/m for automated feeding.


Structural Weldability: Low carbon equivalent values (CEV <= 0.42%) across standard grades prevent heat-affected zone cracking during GMAW/FCAW welding.


Surface Condition: Hot-rolled mill scale supplied as-rolled or shot-blasted (SA 2.5); cold-drawn bars feature a clean finish (Ra 1.6-3.2 um) suitable for direct plating or oxide coating.


Machinability: Uniform cross-sectional grain structure reduces tool wear and prevents deformation during single-point turning, milling, and slotting.

 

Technical Specifications

 

Parameter

Hot-Rolled Flat Bar

Cold-Drawn Flat Bar

Thickness Range

3.0 mm - 60.0 mm (1/8" - 2-1/2")

2.0 mm - 40.0 mm (1/16" - 1-1/2")

Width Range

10.0 mm - 300.0 mm (3/8" - 12")

8.0 mm - 200.0 mm (5/16" - 8")

Standard Lengths

5.8 m, 6.0 m, 12.0 m, or cut-to-size

3.0 m, 6.0 m, or cut-to-size

Thickness Tolerance

+/-0.30 mm to +/-0.80 mm (ISO 286 / EN 10058)

h11 - h12 (ISO 286-2)

Width Tolerance

+/-0.50 mm to +/-1.50 mm

h11 - h12 (ISO 286-2)

Straightness

<= 2.0 mm / 1000 mm

<= 1.0 mm / 1000 mm

Edge Profile

Slightly rounded mill edge

Square edge (sharp 90 deg)

 

Grades & Standards

 

Standard

Grade

Yield Strength (MPa)

Tensile Strength (MPa)

Primary Characteristics

ASTM A36

Carbon Structural

>= 250

400 - 550

General fabrication, easy welding and bending

ASTM A572

Gr. 50 (HSLA)

>= 345

>= 450

Higher load capacity, reduced structural weight

EN 10025-2

S235JR / S275JR

>= 235 / >= 275

360 - 510

Standard European structural grade, certified CVN impact testing

EN 10025-2

S355JR / J2

>= 355

470 - 630

High yield strength for heavy structural machinery

AISI / SAE

1018 / 1045

290 / 310 (Cold Drawn)

440 / 560

1018 for carburizing; 1045 for induction hardening

 

Surface & Processing Options

Surface Conditions

  • As-Rolled (Mill Scale)
  • Shot-Blasted (SA 2.5) & Shop Primed
  • Pickled & Oiled (P&O)
  • Hot-Dip Galvanized (ASTM A123 / EN ISO 1461, coating thickness 55-85 um)
 

Secondary Processing Services

  • Saw Cutting (Tolerance: -0/+2 mm)
  • CNC Chamfering & Deburring
  • Hole Punching & Slotting
  • Heat Treatment: Annealing, Normalizing, or Stress Relieving
 

Applications

 

Machinery & Equipment Base Plates: Cold-drawn 1018/S355 flat bars provide flat mounting surfaces for motor beds, hydraulic manifolds, and linear guide tracks.


Structural Steel Fabrication: ASTM A36 and S275JR hot-rolled flat bars serve as connector plates, stiffeners, gussets, and column base flitches.


Truck & Trailer Manufacturing: High-strength S355 and A572 Gr. 50 sections form side rails, cross-members, and bumper mounts subjected to dynamic payload stresses.


Grating & Architectural Fabrication: Small-dimension flat bars (20x3 mm to 40x5 mm) are slotted, punched, or edge-welded into industrial walkway gratings and stair treads.

 

Quality Control & Inspection

 

Every production heat undergoes non-destructive and mechanical evaluation to confirm compliance with purchase specifications:


Chemical Analysis: Optical Emission Spectroscopy (OES) verification per heat number.


Mechanical Testing: Tensile strength, yield strength, elongation, and Charpy V-notch impact testing (at 20 deg C or -20 deg C per S355J2 requirements).


Dimensional Inspection: Continuous laser gauge monitoring for width, thickness, and camber control.


Documentation: Mill Test Certificates (MTC) supplied according to EN 10204 3.1, detailing heat chemistry, heat treatment parameters, and mechanical values. Third-party inspections (SGS, TUV, BV) available upon request.

 

Supply & Customization Options

Packaging

Steel strapping in 1.0 to 3.0 metric ton bundles with anti-corrosive VCI paper wrap or plastic end shrouds for sea freight export.

Custom Sizes

Non-standard width-to-thickness ratios rolled for minimum order quantities starting at 5 metric tons per size.

Container Loading

Bundles packaged and wood-chocked for 20ft (max 5.8 m lengths) and 40ft open-top or standard containers.

 

What Buyers Should Provide for a Quote

To receive a clear price quote and lead time estimate, please specify:
Steel Grade & Standard: (E.g., ASTM A36, EN 10025 S355J2, AISI 1018)
Delivery Condition: (Hot-Rolled vs. Cold-Drawn)
Exact Dimensions: Thickness x Width x Length (mm or inches)

Surface Finish: (As-rolled, Pickled & Oiled, Shot-blasted SA 2.5, Galvanized)
Quantity: Total tonnage or piece count per size
Processing Requirements: (Cut-to-length tolerances, chamfering, hole patterns)
Destination Port & Incoterms: (FOB, CFR, CIF, or DDP)

 

FAQ

 

Q: What is the difference in edge radius between hot-rolled and cold-drawn flat bar?

A: Hot-rolled flat bars feature a natural mill edge with a small radius dictated by rolling pass design. Cold-drawn flat bars pass through a sizing die, yielding sharp 90-degree corners suitable for flush joints and precision machining.

Q: Can your flat bars be galvanized without surface cracking?

A: Yes. Carbon steel grades A36, S235, and S355 maintain controlled Silicon (Si) and Phosphorus (P) content to prevent hyper-reactivity (Sandelin effect) during hot-dip galvanizing, ensuring uniform zinc adhesion.

Q: What standard tolerances apply if no tolerance class is specified?

A: Hot-rolled flat bars follow EN 10058 / ASTM A6 standard commercial tolerances. Cold-drawn flat bars comply with ISO h11 tolerances unless specified otherwise.

Hot Tags: steel flat bar, China steel flat bar manufacturers, suppliers, factory

Send Inquiry