Boiler Steel Tube

Send Inquiry
Boiler Steel Tube
Details
Boiler steel tubes are pressure-retaining tubular products engineered for heat exchangers, superheaters, reheaters, economizers, and furnace walls. Operating under continuous high temperature and elevated stress, these tubes transfer thermal energy from combustion gases to water or steam without structural degradation or failure.
Category
Steel Pipe & Tube
Share to
Description

Boiler steel tubes are pressure-retaining tubular products engineered for heat exchangers, superheaters, reheaters, economizers, and furnace walls. Operating under continuous high temperature and elevated stress, these tubes transfer thermal energy from combustion gases to water or steam without structural degradation or failure.


Production follows two distinct manufacturing routes: Seamless (SMLS) for high-pressure, severe-temperature environments, and Electric Resistance Welded (ERW / HFW) for low-to-medium pressure heat transfer applications.

 

Key Product Characteristics

 

High-Temperature Creep Rupture Strength: Maintains dimensional stability and mechanical integrity under prolonged stress at temperatures up to 650 deg C (1202 deg F).


Elevated Oxidation and Corrosion Resistance: Resists internal steam oxidation and external fireside ash corrosion, minimizing wall thinning over long operating cycles.


Tight Wall Thickness and OD Tolerances: Cold-drawing and cold-rolling processes deliver strict dimensional uniformity to ensure consistent thermal calculation and predictable flow dynamics.


Bending and Flaring Capability: Ductility parameters allow tight-radius cold bending, expanding, and flaring during boiler header and coil fabrication without surface micro-cracking.


Uniform Metallurgical Structure: Controlled heat treatment ensures consistent grain size, eliminating localized stress concentration zones.

 

Technical Specifications

 

Parameter

Specification / Range

Outer Diameter (OD)

15.9 mm - 168.3 mm (5/8 in - 6-5/8 in)

Wall Thickness (WT)

1.65 mm - 25.4 mm (0.065 in - 1.000 in); Minimum Wall (MW) or Nominal Wall (NW)

Manufacturing Method

Hot-Finished Seamless (HFS), Cold-Drawn Seamless (CDS), Electric Resistance Welded (ERW)

Length

6.0 m - 18.0 m, Single Random, Double Random, or Fixed Length (+/- 3mm tolerance)

Ends Preparation

Plain Ends (PE), Beveled Ends (BE per ASME B16.25), Square Cut, Deburred

Delivery Conditions

Normalized & Tempered (N+T), Quenched & Tempered (Q+T), Isothermal Annealed, Bright Annealed (BA)

 

Grades & Standards

 

Standard

Grade

Steel Type

Primary Service Temperature / Application

ASME SA178 / ASTM A178

Grade A, C, D

Carbon Steel / Manganese Steel

ERW Boiler tubes, superheaters, and boiler flues

ASME SA192 / ASTM A192

SA192

Seamless Carbon Steel

High-pressure seamless boiler and superheater tubes

ASME SA210 / ASTM A210

Grade A-1, C

Medium-Carbon Steel

Seamless boiler tubes, furnace tubes, and flues

ASME SA213 / ASTM A213

T11, T22, T91, T92

Low / High-Alloy Steel

High-temperature superheaters and reheaters

EN 10216-2

P235GH, P265GH, 16Mo3, 13CrMo4-5, 10CrMo9-10

Non-alloy & Alloy Steel

European pressure equipment (PED 2014/68/EU compliant)

DIN 17175

ST35.8, ST45.8, 15Mo3, 13CrMo44

Heat-Resistant Steel

High-pressure vessels and pipework

 

Surface & Processing Options

 

Heat Treatment: Full annealing, normalizing at 880 deg C to 980 deg C, tempering at 650 deg C to 760 deg C, or bright annealing in protective atmospheres to prevent scale formation.


Surface Protection: Light varnish coating, black painting, rust-inhibiting oil, or un-oiled for immediate welding integration.


End Finishing: Plastic end caps for port protection; beveling at 30 deg to 35 deg angle for field butt-welding.


Secondary Fabrication: Precision cutting, U-bending with post-bend stress-relief heat treatment, end swaging, and finning (longitudinal or helical).

 

Applications

01/

Power Generation Boilers: Main steam lines, superheater coils, and reheater banks in coal-fired, gas-fired, and biomass power plants.

02/

Industrial Heat Exchangers: Shell-and-tube units in oil refineries, petrochemical processing plants, and chemical reactors.

03/

Economizers & Waste Heat Recovery: Flue gas energy recovery systems and heat recovery steam generators (HRSG).

04/

Marine & Locomotive Boilers: Firetube and watertube marine steam generation systems.

Quality Control & Inspection

 

Every production lot undergoes non-destructive and destructive testing in compliance with ASME Section II Part A and EN 10204:


Non-Destructive Testing (NDT): 100% Eddy Current Testing (ECT) per ASTM E309 or Ultrasonic Testing (UT) per ASTM E213; 100% Hydrostatic Testing (up to 30 MPa) held for minimum 5 seconds.


Mechanical Testing: Tensile strength, yield strength, elongation, Flattening Test (ASTM A450), Flaring/Expanding Test, and Charpy V-Notch Impact Test at low temperatures.


Metallurgical Analysis: Chemical composition verification via optical emission spectrometry (OES), grain size measurement (ASTM E112), and microstructural examination for decarburization depth.


Certification: EN 10204 3.1 Material Test Report (MTR) provided as standard; EN 10204 3.2 Third-Party Inspection (TUV, SGS, BV, Lloyd's Register) available upon request.

 

Supply & Customization Options

 

U-Bent Tubes: Fabricated to ASME SA213/SA192 specifications with leg lengths up to 12 meters; bend area heat-treated and dye-penetrant tested.


Custom Tolerances: Tighter wall thickness tolerances (e.g., +10%/-0% on Minimum Wall) for weight control and heat transfer calculations.


Packaging: Hexagonal bundles wrapped with waterproof paper, steel strapping, and wooden box packaging for ocean freight preservation.

 

What Buyers Should Provide for a Quote

To receive an accurate technical quotation and production schedule, submit the following engineering parameters:
Standard & Grade: (E.g., ASME SA213 Grade T22 or EN 10216-2 13CrMo4-5)
Manufacturing Method: Seamless (SMLS) or Welded (ERW)
Dimensions: Outer Diameter (OD) x Wall Thickness (WT) x Length (indicate if WT is Minimum Wall or Nominal Wall)

 

Quantity: Total meters, feet, or metric tons
Heat Treatment Condition: (E.g., Normalized & Tempered)
Testing & Inspection Requirements: Specific NDT methods, Third-Party Inspection (TPI), or EN 10204 3.2 certification requirements
End Use / Operating Conditions: Temperature, pressure, and fluid medium (if alternative grade validation is needed)

 

FAQ

 

Q: What is the difference between Minimum Wall (MW) and Nominal Wall (NW) boiler tubes?

A: Minimum Wall guarantees that the wall thickness will not fall below the specified dimension at any point (tolerance typically +20%/-0% or +22%/-0%). Nominal Wall allows a symmetric tolerance around the target thickness (typically +/-10% or +/-12.5%). ASME boiler codes frequently mandate Minimum Wall for safety-critical pressure calculations.

Q: When should I select ASME SA213 T91 over SA213 T22?

A: Grade T91 (9% Cr, 1% Mo, V, Nb) offers significantly higher creep-rupture strength at operating temperatures above 560 deg C (1040 deg F) compared to Grade T22 (2.25% Cr, 1% Mo). T91 allows thinner tube walls for high-pressure superheaters, reducing thermal stress and total boiler weight.

Q: Are EN 10216-2 P235GH tubes directly interchangeable with ASTM A192?

A: Both are seamless carbon steel tubes intended for elevated temperature service. While chemical compositions and tensile properties overlap closely, structural engineering compliance depends on the design code (ASME Boiler & Pressure Vessel Code vs. European Pressure Equipment Directive PED). Verification of local regulatory approval is required before substitution.

Hot Tags: boiler steel tube, China boiler steel tube manufacturers, suppliers, factory

Send Inquiry